Re: Christmas and USB devices question

On Sun, 2004-12-26 at 01:30 -0900, adam bultman wrote:
> What I do for my USB stuff ( mostly my camera) I'll boot the system with
> the USB disconnected; then once it's booted, put in the USB device,
> power it on (if necessary) and then the system (if the module is loaded
> correctly) will say something about a scsi disk, which you can then mount.
>
> For me, it's /dev/sda. I always do it *last* because that makes it
> easier to identify.
>
> Adam
>
Hi Adam,

But in this case, all my SCSI devices are up and then I have a hard time
figuring which device to mount for the MP3 player ?
/dev/md0 on /work type reiserfs (rw,noexec,nosuid,nodev,acl) is a
software raid 5 divice, with all of the following

> >Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> >Attached scsi generic sg1 at scsi0, channel 0, id 8, lun 0, type 5
> >Attached scsi generic sg2 at scsi1, channel 0, id 0, lun 0, type 0
> >Attached scsi generic sg3 at scsi1, channel 0, id 1, lun 0, type 0
> >Attached scsi generic sg4 at scsi1, channel 0, id 2, lun 0, type 0
> >Attached scsi generic sg5 at scsi1, channel 0, id 3, lun 0, type 0
> >Attached scsi generic sg6 at scsi1, channel 0, id 4, lun 0, type 0
> >Attached scsi generic sg7 at scsi1, channel 0, id 5, lun 0, type 0
> >Attached scsi generic sg8 at scsi1, channel 0, id 6, lun 0, type 0
> >

When I plug it in it says in /var/log/messages

Dec 25 16:40:18 papa kernel: usb 1-2: new full speed USB device using
address 6
Dec 25 16:40:19 papa kernel: usb 1-2: Product: TDK UniFi Audio Player
Dec 25 16:40:19 papa kernel: usb 1-2: Manufacturer: TDK UniFi
 

So the USB sub-system sees it OK.

sda & sdb are my hard drives, with all of the others being the md0
devices.

Any other ideas ?

> W.D.McKinney wrote:
>
> >Hope everyone is having a wonderful holiday this Christmas.
> >
> >I have a little MP3 player that I would like to use with Linux.
> >
> ># cat /proc/bus/usb/devices
> >
> >T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
> >D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> >P: Vendor=2735 ProdID=0091 Rev= 1.00
> >S: Manufacturer=TDK UniFi
> >S: Product=TDK UniFi Audio Player
> >C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 20mA
> >I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> >E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> >E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> >E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
> >
> >/var/log/messages has
> >
> >Dec 25 14:39:15 papa kernel: usb 1-2: new full speed USB device using
> >address 5
> >Dec 25 14:39:16 papa kernel: usb 1-2: Product: TDK UniFi Audio Player
> >Dec 25 14:39:16 papa kernel: usb 1-2: Manufacturer: TDK UniFi
> >
> >This in on my all SCSI workstation. So I am wondering how to mout this
> >unit ? /dev/sda1 is already in use of course.
> >
> >I have:
> >
> >scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
> > <Adaptec 29160N Ultra160 SCSI adapter>
> > aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
> >
> >(scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 63, 16bit)
> >(scsi0:A:8): 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
> > Vendor: SEAGATE Model: ST336607LW Rev: 0007
> > Type: Direct-Access ANSI SCSI revision: 03
> >scsi0:A:0:0: Tagged Queuing enabled. Depth 32
> >SCSI device sda: 71687372 512-byte hdwr sectors (36704 MB)
> >SCSI device sda: drive cache: write back
> > sda: sda1 sda2
> >Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> > Vendor: PLEXTOR Model: CD-ROM PX-40TW Rev: 1.01
> > Type: CD-ROM ANSI SCSI revision: 02
> >scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
> > <Adaptec 3940 SCSI adapter>
> > aic7870: Wide Channel A, SCSI Id=7, 16/253 SCBs
> >
> >(scsi1:A:0): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> > Vendor: COMPAQ Model: BB01811C9C Rev: 3B05
> > Type: Direct-Access ANSI SCSI revision: 02
> >scsi1:A:0:0: Tagged Queuing enabled. Depth 32
> >SCSI device sdb: 35565080 512-byte hdwr sectors (18209 MB)
> >SCSI device sdb: drive cache: write through
> > sdb: sdb1
> >Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
> >(scsi1:A:1): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> > Vendor: DEC Model: RZ2EA-LA (C) DEC Rev: N1H1
> > Type: Direct-Access ANSI SCSI revision: 02
> >scsi1:A:1:0: Tagged Queuing enabled. Depth 32
> >SCSI device sdc: 35565080 512-byte hdwr sectors (18209 MB)
> >SCSI device sdc: drive cache: write through
> > sdc: sdc1
> >Attached scsi disk sdc at scsi1, channel 0, id 1, lun 0
> >(scsi1:A:2): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> > Vendor: COMPAQ Model: BB01811C9C Rev: 3B05
> > Type: Direct-Access ANSI SCSI revision: 02
> >scsi1:A:2:0: Tagged Queuing enabled. Depth 32
> >SCSI device sdd: 35565080 512-byte hdwr sectors (18209 MB)
> >SCSI device sdd: drive cache: write through
> > sdd: sdd1
> >Attached scsi disk sdd at scsi1, channel 0, id 2, lun 0
> >(scsi1:A:3): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> > Vendor: COMPAQ Model: BB01811C9C Rev: 3B05
> > Type: Direct-Access ANSI SCSI revision: 02
> >scsi1:A:3:0: Tagged Queuing enabled. Depth 32
> >SCSI device sde: 35565080 512-byte hdwr sectors (18209 MB)
> >SCSI device sde: drive cache: write through
> > sde: sde1
> >Attached scsi disk sde at scsi1, channel 0, id 3, lun 0
> >(scsi1:A:4): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> > Vendor: COMPAQ Model: BB01811C9C Rev: 3B05
> > Type: Direct-Access ANSI SCSI revision: 02
> >scsi1:A:4:0: Tagged Queuing enabled. Depth 32
> >SCSI device sdf: 35565080 512-byte hdwr sectors (18209 MB)
> >SCSI device sdf: drive cache: write through
> > sdf: sdf1
> >Attached scsi disk sdf at scsi1, channel 0, id 4, lun 0
> >(scsi1:A:5): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> > Vendor: COMPAQ Model: BB01811C9C Rev: 3B05
> > Type: Direct-Access ANSI SCSI revision: 02
> >scsi1:A:5:0: Tagged Queuing enabled. Depth 32
> >SCSI device sdg: 35565080 512-byte hdwr sectors (18209 MB)
> >SCSI device sdg: drive cache: write through
> > sdg: sdg1
> >Attached scsi disk sdg at scsi1, channel 0, id 5, lun 0
> >(scsi1:A:6): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
> > Vendor: Quantum Model: XP39100J Rev: LYJ0
> > Type: Direct-Access ANSI SCSI revision: 02
> >scsi1:A:6:0: Tagged Queuing enabled. Depth 32
> >SCSI device sdh: 17773524 512-byte hdwr sectors (9100 MB)
> >SCSI device sdh: drive cache: write through
> > sdh: sdh1
> >Attached scsi disk sdh at scsi1, channel 0, id 6, lun 0
> >scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
> > <Adaptec 3940 SCSI adapter>
> > aic7870: Wide Channel B, SCSI Id=7, 16/253 SCBs
> >
> >
> >
> >hda: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache
> >Uniform CD-ROM driver Revision: 3.20
> >hdc: ATAPI 24X DVD-ROM drive, 512kB Cache
> >sr0: scsi-1 drive
> >Attached scsi CD-ROM sr0 at scsi0, channel 0, id 8, lun 0
> >st: Version 20040403, fixed bufsize 32768, s/g segs 256
> >Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> >Attached scsi generic sg1 at scsi0, channel 0, id 8, lun 0, type 5
> >Attached scsi generic sg2 at scsi1, channel 0, id 0, lun 0, type 0
> >Attached scsi generic sg3 at scsi1, channel 0, id 1, lun 0, type 0
> >Attached scsi generic sg4 at scsi1, channel 0, id 2, lun 0, type 0
> >Attached scsi generic sg5 at scsi1, channel 0, id 3, lun 0, type 0
> >Attached scsi generic sg6 at scsi1, channel 0, id 4, lun 0, type 0
> >Attached scsi generic sg7 at scsi1, channel 0, id 5, lun 0, type 0
> >Attached scsi generic sg8 at scsi1, channel 0, id 6, lun 0, type 0
> >
> >
> >etc.
> >
> >
> >So I was wondering how to mount the USB device ?
> >
> >Thanks,
> >Dee
> >
> >
> >
> >---------
> >To unsubscribe, send email to <aklug-request@aklug.org>
> >with 'unsubscribe' in the message body.
> >
> >
> >
>
>

---------
To unsubscribe, send email to <aklug-request@aklug.org>
with 'unsubscribe' in the message body.
Received on Sat Dec 25 16:43:28 2004