Re: ipcop and serial ports


Subject: Re: ipcop and serial ports
From: Fielder George Dowding (fgdowding@iceworm-enterprises.net)
Date: Mon Apr 28 2003 - 15:00:56 AKDT


Hmmmm... Does it have the "setserial" utility?

On Mon, 28 Apr 2003 13:57:19 -0800
Jim Gribbin <jewelrysupplier@gci.net> wrote:

> Nice try, but ipcop doesn't have a serial.conf. At least not in
> /etc. I'm still looking to see if I can find it somewhere else as
> ipcop seems to have moved or hidden some of scripts for security
> reasons.
>
> I may take a shot at just creating one and see if it uses it.
>
> Jim Gribbin
>
> On Mon, 2003-04-28 at 11:14, Fielder George Dowding wrote:
> > Greetings Jim and all,
> >
> > Under the 2.4 kernel, serial port setup is handled in a new and
> > better way, really :)
> >
> > Look in the file /etc/serial.conf
> >
> > Read the man page for setserial
> >
> > You will probably have to edit serial.conf to reflect the
> > desired ttyS<n>, IRQ, and I/O address. The card you are talking
> > about may be listed in serial.conf. In any case, look for the
> > stanzas that set the ports to the ones you are getting and edit
> > them to the ones you want.
> >
> > fgd.
> >
> > On 27 Apr 2003 22:26:57 -0800
> > Jim Gribbin <jgribbin@alaska.net> wrote:
> >
> > >
> > > I don't think I'm doing a good job at describing my serial
> > > port problem, so I'll try a little different tact.
> > >
> > > I have a pci high speed port card with 2-serial & 1-parallel
> > > ports.
> > >
> > > Under the 2.2 kernel, /proc/pci showed an unknown card mfg'd
> > > by Timedia in a particular slot with 3-ports and an irq.
> > > Apparently because the card was unknown, Linux did nothing
> > > with the ports and I could assign the ports using setserial's
> > > port option to whatever available /dev/ttySx were available.
> > >
> > > Under the 2.4 kernel, Linux seems to know what the card is.
> > > /proc/pci now shows a multi-port card mfg'd by Timedia (I
> > > don't recall the exact wording, but the card is now known)
> > > with 2-serial ports and a parallel port. Because Linux now
> > > knows the card, it is assigning the ports for me. But I want
> > > them assigned elsewhere and Linux won't let me do it has them
> > > already assigned.
> > >
> > > Clear as mud now? :-)
> > >
> > > Jim Gribbin
> > >
> > >
> > >
> > > ---------
> > > To unsubscribe, send email to <aklug-request@aklug.org>
> > > with 'unsubscribe' in the message body.
> > >
> > >
> > >
> >
>
>
>

-- 
Fielder George Dowding, Chief Iceworm
dba Iceworm Enterprises, Anchorage, Alaska
Since 1976 - Over 25 Years of Service.

--------- To unsubscribe, send email to <aklug-request@aklug.org> with 'unsubscribe' in the message body.



This archive was generated by hypermail 2a23 : Mon Apr 28 2003 - 14:50:22 AKDT