Subject: Re: cdrecord
From: Adam Elkins (i-robot@gci.net)
Date: Wed Jan 22 2003 - 18:07:45 AKST
Well, I feel better knowing you get the same error...As far as mounting the drive inside my box, all the connections fit.
Adam
On Wed, 22 Jan 2003 11:15:44 -0900
Jim Gribbin <jewelrysupplier@gci.net> wrote:
>
> It should be working as it is. Besides, I don't think you'll get the
> bezel to fit.
>
> I just tried a CD in mine. I get the same warning. I hadn't noticed it
> before, probably because I usually use Xcdroast. I haven't had any
> problems and I just burned and verified a disk using your same command
> line.
>
> I suspect that this warning is coming about because this drive isn't in
> cdrecord's database, so it's response when queried is unrecognized
> causing the program to use a generic instruction set. Seems to work
> fine though.
>
> One thing I've noticed, DAO (Disk at Once) doesn't seem to work on this
> drive.
>
> Jim Gribbin
>
> On Tue, 2003-01-21 at 17:11, Adam Elkins wrote:
> > Resources _shouldn't_ be a problem...I'm running an AMD 1.5ghz Duron, 512 ram, and I run blackbox/fluxbox mostly...
> > It's writing fine (or seems to, the cd's work). Could it simply be because it's using scsi emulation for the usb?
> > All this brings up another question; If I take the drive out of it's facny purple case and take off the little card on back (Which makes it usb and provides power) and hook it up like a regular cdrom, will it work?
> >
> > Adam
> >
> >
> >
> > On Tue, 21 Jan 2003 10:55:06 -0900
> > Jim Gribbin <jewelrysupplier@gci.net> wrote:
> >
> > > What kind of hardware resources do you have on the box? I ask this
> > > because I also have a ZipCD USB and when I was running it on a limited
> > > resource box, K6-300/64MB, I could only burn mini-CDs. That box with the
> > > overhead of a 2.4 kernel just didn't seem to be able to keep up with
> > > more than a 200MB burn. I don't recall the error messages I was getting
> > > though.
> > >
> > > Jim Gribbin
> > >
> > > On Tue, 2003-01-21 at 08:06, Adam Elkins wrote:
> > > > On Tue, 21 Jan 2003 09:20:17 -0700 (MST)
> > > > "Christopher E. Brown" <cbrown@woods.net> wrote:
> > > >
> > > > >
> > > > > On Mon, 20 Jan 2003, Adam Elkins wrote:
> > > > >
> > > > > >
> > > > > > When using cdrecord, I get this;
> > > > > >
> > > > > > cdrecord: Warning: controller creates hard SCSI failure when retrieving CD capaities page.
> > > > > >
> > > > > > The cd continues to burn though, but I doesn't work (for iso's anyway)
> > > > > >
> > > > > > Any thoughts?
> > > > > >
> > > > > > Adam
> > > > >
> > > > >
> > > > >
> > > > > Well, the SCSI host adapter brand and model, the driver you are using
> > > > > for it, kernel version, cdburner brand/model, the reported bus/id/lun
> > > > > for the CDR, notes on the cabling and termination config and any other
> > > > > devices on the bus would be helpful.
> > > > >
> > > > >
> > > > > Or if using ATAPI, detailed on your IDE bus setup for both channels,
> > > > > etc...
> > > > >
> > > > >
> > > > > --
> > > > > I route, therefore you are.
> > > > >
> > > > >
> > > > > ---------
> > > > > To unsubscribe, send email to <aklug-request@aklug.org>
> > > > > with 'unsubscribe' in the message body.
> > > > >
> > > >
> > > > I'm using a Iomega ZipCD 650. usb. I tried again with another iso, and it burned fine, but I still got the error.
> > > > Other than that, Slackware 8.1, 2.4.18 stock kernel and as mentioned, it's a usb drive.
> > > > Comand I used 'cdrecord dev=0,0,0 speed=4 -eject <isofilehere>'
> > > >
> > > > Adam
> > > >
> > > > ---------
> > > > To unsubscribe, send email to <aklug-request@aklug.org>
> > > > with 'unsubscribe' in the message body.
> > > >
> > >
> >
> > ---------
> > To unsubscribe, send email to <aklug-request@aklug.org>
> > with 'unsubscribe' in the message body.
> >
>
>
> ---------
> To unsubscribe, send email to <aklug-request@aklug.org>
> with 'unsubscribe' in the message body.
>
---------
To unsubscribe, send email to <aklug-request@aklug.org>
with 'unsubscribe' in the message body.
This archive was generated by hypermail 2a23 : Wed Jan 22 2003 - 18:04:54 AKST