Subject: Re: cdrecord
From: Adam Elkins (i-robot@gci.net)
Date: Tue Jan 21 2003 - 17:11:43 AKST
Resources _shouldn't_ be a problem...I'm running an AMD 1.5ghz Duron, 512 ram, and I run blackbox/fluxbox mostly...
It's writing fine (or seems to, the cd's work). Could it simply be because it's using scsi emulation for the usb?
All this brings up another question; If I take the drive out of it's facny purple case and take off the little card on back (Which makes it usb and provides power) and hook it up like a regular cdrom, will it work?
Adam
On Tue, 21 Jan 2003 10:55:06 -0900
Jim Gribbin <jewelrysupplier@gci.net> wrote:
> What kind of hardware resources do you have on the box? I ask this
> because I also have a ZipCD USB and when I was running it on a limited
> resource box, K6-300/64MB, I could only burn mini-CDs. That box with the
> overhead of a 2.4 kernel just didn't seem to be able to keep up with
> more than a 200MB burn. I don't recall the error messages I was getting
> though.
>
> Jim Gribbin
>
> On Tue, 2003-01-21 at 08:06, Adam Elkins wrote:
> > On Tue, 21 Jan 2003 09:20:17 -0700 (MST)
> > "Christopher E. Brown" <cbrown@woods.net> wrote:
> >
> > >
> > > On Mon, 20 Jan 2003, Adam Elkins wrote:
> > >
> > > >
> > > > When using cdrecord, I get this;
> > > >
> > > > cdrecord: Warning: controller creates hard SCSI failure when retrieving CD capaities page.
> > > >
> > > > The cd continues to burn though, but I doesn't work (for iso's anyway)
> > > >
> > > > Any thoughts?
> > > >
> > > > Adam
> > >
> > >
> > >
> > > Well, the SCSI host adapter brand and model, the driver you are using
> > > for it, kernel version, cdburner brand/model, the reported bus/id/lun
> > > for the CDR, notes on the cabling and termination config and any other
> > > devices on the bus would be helpful.
> > >
> > >
> > > Or if using ATAPI, detailed on your IDE bus setup for both channels,
> > > etc...
> > >
> > >
> > > --
> > > I route, therefore you are.
> > >
> > >
> > > ---------
> > > To unsubscribe, send email to <aklug-request@aklug.org>
> > > with 'unsubscribe' in the message body.
> > >
> >
> > I'm using a Iomega ZipCD 650. usb. I tried again with another iso, and it burned fine, but I still got the error.
> > Other than that, Slackware 8.1, 2.4.18 stock kernel and as mentioned, it's a usb drive.
> > Comand I used 'cdrecord dev=0,0,0 speed=4 -eject <isofilehere>'
> >
> > Adam
> >
> > ---------
> > To unsubscribe, send email to <aklug-request@aklug.org>
> > with 'unsubscribe' in the message body.
> >
>
---------
To unsubscribe, send email to <aklug-request@aklug.org>
with 'unsubscribe' in the message body.
This archive was generated by hypermail 2a23 : Tue Jan 21 2003 - 17:09:08 AKST